SA1401 is solvent freeα -cyanoacrylate adhesive. It polymerizes with moisture in air. It's insensitive to the surface, general purpose,
Medium viscosity and bonds instantly.
Usage
Designed for bonding inert materials, hard to bond material, porous, acetic surface and absorbent material, such as plastic, rubber, leather, wood and cardboard etc.
Operation
1. Cleaning the surfaces that to be glued and coated, removing the rust, dust, greasy dirt and other
Foreign matter and substance. PUNADE cleaner SA6755 is recommended.
2. Apply the product to one surface(or two surfaces), then press the two surfaces instantly.
3. Apply the glue in small quantity for better effect.
3. PUNADE activator SA6712 can make the curing faster, dispense it on one surface, after solvent
Volatilizing, apply the adhesive on the other surface. Then press the two surfaces instantly.
4. For hard to bond material, use PUNADE primer SA6770. Spray it evenly on one surface and wait
To dry, press instantly after applying glue to the other surface.
Attention
1. Keep out of reach of children.
2. The product contains cyanoacrylate, which may irritate skin and eyes. So it is recommended to
Use the product at a well ventilated place.
4. The product can bond skin and eyes instantly, so please wear goggle and glove before operating.
5. In case of contact with skin, DIP in warm soap water and peel off the glue from skin. Do not use
Knife to peel off.
6. In case of contact with eyes, rinse with clean water immediately and call a medical attention.
Package
20g/bottle
Safety Operation Material
MSDS isn't included here. Please read TDS, MSDS and label carefully before operation. You can get MSDS from Sepuna or other distributors, or mail to service center sepuna046@sepuna. Cn, or call +86-400-882-1323.
Product Warranty
All product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advices we supply don't apply in any circumstances. Sepuna don't make assurance of any other applications outside the specification until Sepuna supply a special written guarantee. Sepuna is only responsible to replace or refund if this product is defective within the warranty period stated above. Sepuna makes it clear that will not be liable of any accidents.
Properties before curing |
Testing Term |
testing standard |
Unit |
Typical Value |
Range |
|
Appearance |
By Eye |
--- |
Transparent liquid |
|
|
Basis Material |
|
|
α- Cyanoacrylate ethyl ester |
|
|
Viscosity |
GB/T 2794-1995 |
Brookfield HB T-C spindle 30 rpm, mPa@s |
110 |
90-140 |
|
Density |
GB/T13354-1992 |
25ºC,g/cm3 |
1.10 |
|
|
Fixture |
|
S |
|
<20 |
|
Flash point |
SH/T0733-2004 |
ºC |
|
>93 |
|
Max.Gap fill |
|
mm |
0.1 |
|
Properties after curing |
Full curing time |
|
h |
24 |
|
|
Shear Strength |
GB/T18747.2-2002 |
MPa |
22 |
|
|
Working Temperature |
|
ºC |
|
-55-83 |
|
Aging under the conditions below and tested at 22ºC |
Chemical/Solvent Resistance |
Solvent |
Temperature |
% of Initial Strength |
|
|
ºC |
100h |
500h |
1000h |
|
Lubricating Oil |
40 |
95 |
95 |
95 |
|
Leaded Gasoline |
22 |
100 |
100 |
100 |
|
Ethanol |
22 |
100 |
100 |
100 |
|
Isopropanol |
22 |
100 |
100 |
100 |
|
RH95% |
40 |
70 |
50 |
40 |
|
RH95%(PC) |
40 |
100 |
100 |
100 |
Founded in DEC. 2003, SEPUNA has been engaged in researching, manufacturing and marketing automobile sealant and adhesive for 9 years.
Since the foundation, SEPUNA Chemical has been focusing on adhesive's researching and application. Then in 2005, We acquired PUNADE technology which is from Switzerland.
Within 9 years, SEPUNA mainly develops Silicone, Polyurethane and Epoxy resin adhesives. And in the future, we will enlarge our line to Unsaturated, Natural and Acrylic Resin adhesive.
After 9 years' improvement, by the keep researching and innovation, SEPUNA is already a mature adhesive supplier with the core competitiveness.