Acid Free Reinforced Anchor Adhesive with Special Glue Gun

acid free reinforced anchor adhesive with special glue gun

 
Kastar adhesive for bar planting
 
Application:
 
Planting bar adhesive is a two-component epoxy resin modified structural adhesive, drilling anchoring is suitable for various kinds of steel, bolts and various metal material and concrete, rock, brick and other solid substrates, steel bars are widely used in building structure, the screw implant. Building structure reinforcement, anchorage. Frame structure, shear strong anchorage. A variety of equipment foundation fixed. Railway, highway, bridge, water conservancy renovation, expansion project reinforcement. Equipment foundation bolt installation, road bar reinforcement and other occasions.


Characteristic:
 
1, AB two-component mixing ratio: 1:1, excellent thixotropy, convenient and fast construction
2, on the bare force of anchoring large reinforced, high strength, strong adhesion, as embedded.
3, after curing, toughness, excellent anti impact ability, excellent earthquake resistance.
4, anti-aging, durable, weather resistance, resistance to medium (acid, alkali, salt, water) with excellent performance
5, do not contain volatile solvent, non-toxic environmental protection, environmental friendly.


Operation Points:
1, the construction environment should be ventilated and dry, use a pump drill and brush thoroughly clean, where there is oil clean with acetone.
2, the test must be carried out in accordance with the modulation glue environment, temperature and process conditions prior to use to determine the best ratio.
3, room temperature curing adhesive temperature of not less than 5 °C, 20-25 °C ambient temperature curing time of less than three days, at 10 °C ambient temperature curing time of not less than seven days; cryogenic rubber in -15 ~ 0 °C environment temperature curing.
4. Do not touch the front completely cured reinforced or screw, otherwise it will affect the anchoring effect.
5, in order to ensure the A, B two-component mixing, with mechanical agitation is appropriate.
 
 
Construction Process:
1, Drilling the hole according to the provisions of the diameter and the depth (drilling depth is generally about 10-20ddiameter greater than the diameter of rebar, reinforced 4-8mm);
2, use the brush and blowing the hole clean.
3, from the bottom of the hole the colloid injection hole in 1/2~2/3 mill.
4, screwing the reinforcement or screwed into the screw hole slowly

 

Performance index
Performance Project			Performance Requirements	Test results
Adhesive performance	Splitting tensile strength(Mpa)		≥8.5	14.1
	Flexural strength (Mpa)		≥50	51.2
	Compressive strength(Mpa)		≥60	74
	Steel - steel (steel sleeve method) tensile shear strength standard value(Mpa)		≥16	18
	The bonding strength of ribbed steel bars and concrete under the constraint of drawing(Mpa)	C60 Φ25 L=175cm	≥11.0	13.5
		C60 Φ25 L=175	≥17.0	21.3
Non-volatile content (solid content)(%)			≥99	99.6
90d heat aging Steel - steel tensile shear strength retention(%)			≥90	93.0
Freeze-thaw cycle 50 times Steel - steel tensile shear strength retention(%)			≤5	Reduce3.1

 
 

Dosage: the number of inserted bar glue per kg planted (experience)
The diameter of screw thread steel(mm)	10	12	14	46	18	20	22	25	28
Plant root number (/KG)	20	15	12	10	8	5	3	2	1
Drilling depth	15D(D:Bar diameter)

Specifications:
400ml/pair 25pair/big box
500g/pair 24pair/big box
Size:35*25*29.5(cm)
 
 
Directions:

1 .The operator must wear the working suit, blinkers, respirator, and leather 
gloves.
 
2.Only a few people may be sensitive to the adhesive. The symptom will stop if they keep away from it.
 
3.The adhesive must be kept off children, and your mouth and eyes. In the 
event of its touch of mouth and eyes, flush with fresh water or see a physician.
 
4.In the event of batches, make a pre-test to avoid the negative effect of improper operation.
 
 
Thank you for visiting. Any questions, please feel free to contact us. I am Ruiqiang Wu here.