XZS560 Hedge Trimmer |
Model XZS560 |
Gasoline Engine TH23-DX |
Speed idle speed (rpm) 3000 |
Maximum speed (rpm) 11000 |
Displacement (cc) 23.6 |
Fuel tank capacity (l) 0.47 |
The minimum fuel consumption rate (g / kwh) 449 |
Maximum output power (kw / rpm) 0.74 / 7500 |
Reduction ratio 5.11 |
Dimension (L × W × H) (mm) 1074 × 266 × 207 |
Machine weight (kg) 5.64 |
Mechanical Maintenance of common sense:
1. Gasoline prohibit speeding and should be shut down at low speeds.
2, the oil to the right, genuine, clean gasoline to clean, fresh.
3, non-professionals can not adjust the carburetor. We must adjust, generally
After the needle gently clockwise to tighten, then counterclockwise twist 1.5-1.75 weeks.
4, the air filter should always check with soapy water or regularly
Replace.
5, 100-300 hours of operation of the gasoline engine, the application of wood or bamboo Clear
Coke once. Remove the cylinder head when cleared, remove the cylinder, cylinder head, live
Plugs, valves, etc. attached to carbon. Coke not enter the bore and the valve
Seat.
6, to maintain clean cylinder gasoline engine especially fins.
7, refueling, inspection, repair, maintenance, you should disconnect the spark plug cap, not
To smoke, away from open flame.
8, not in the operating room. In addition to the operator when the machine is working outside, unrelated persons
Leave the machine more than 15 meters.
9, before and after each use machine inspection section and other parts of the bolt
Tightness.
10, there is a clutch, the clutch that is exposed installation of the machine is not good
Before the gasoline engine may not start.
11, other lubricating parts of the machine, follow the instructions to add regularly needed
NOTE lubricating oil or grease.
Mechanical Maintenance of common sense:
1. Gasoline prohibit speeding and should be shut down at low speeds.
2, the oil to the right, genuine, clean gasoline to clean, fresh.
3, non-professionals can not adjust the carburetor. We must adjust, generally
After the needle gently clockwise to tighten, then counterclockwise twist 1.5-1.75 weeks.
4, the air filter should always check with soapy water or regularly
Replace.
5, 100-300 hours of operation of the gasoline engine, the application of wood or bamboo Clear
Coke once. Remove the cylinder head when cleared, remove the cylinder, cylinder head, live
Plugs, valves, etc. attached to carbon. Coke not enter the bore and the valve
Seat.
6, to maintain clean cylinder gasoline engine especially fins.
7, refueling, inspection, repair, maintenance, you should disconnect the spark plug cap, not
To smoke, away from open flame.
8, not in the operating room. In addition to the operator when the machine is working outside, unrelated persons
Leave the machine more than 15 meters.
9, before and after each use machine inspection section and other parts of the bolt
Tightness.
10, there is a clutch, the clutch that is exposed installation of the machine is not good
Before the gasoline engine may not start.
11, other lubricating parts of the machine, follow the instructions to add regularly needed
NOTE lubricating oil or grease.
Mechanical Maintenance of common sense:
1. Gasoline prohibit speeding and should be shut down at low speeds.
2, the oil to the right, genuine, clean gasoline to clean, fresh.
3, non-professionals can not adjust the carburetor. We must adjust, generally
After the needle gently clockwise to tighten, then counterclockwise twist 1.5-1.75 weeks.
4, the air filter should always check with soapy water or regularly
Replace.
5, 100-300 hours of operation of the gasoline engine, the application of wood or bamboo Clear
Coke once. Remove the cylinder head when cleared, remove the cylinder, cylinder head, live
Plugs, valves, etc. attached to carbon. Coke not enter the bore and the valve
Seat.
6, to maintain clean cylinder gasoline engine especially fins.
7, refueling, inspection, repair, maintenance, you should disconnect the spark plug cap, not
To smoke, away from open flame.
8, not in the operating room. In addition to the operator when the machine is working outside, unrelated persons
Leave the machine more than 15 meters.
9, before and after each use machine inspection section and other parts of the bolt
Tightness.
10, there is a clutch, the clutch that is exposed installation of the machine is not good
Before the gasoline engine may not start.
11, other lubricating parts of the machine, follow the instructions to add regularly needed
NOTE lubricating oil or grease.
The related production
Our company is a Japanese-owned enterprise, which was established in June, 2001, located besides the overhead, in Longjiang Road, Economic Development Zone, Zhong building, covering about 10, 000 square meters. It is a high-tech enterprise specializing in the development, design, manufacturing, sales and service of small mower and gear.
Our main equipment: A large number of high precision machines, such as multifunctional gear manufacturing machine, multi-axis CNC lathe, automatic feed lathe, high precision CNC lathe, multifunctional cylindrical grinding machine tool, precision thread rolling machine, precision grinding machine, precision grinding lathe, automatic knurling machine, spline broaching machine, precision chamfering machine, three times detector, gear bear detector, gear meshing detector, and CASE detector, etc.
Gear has played the common role in current society structure and machines, especially one important role in human relations and social order. If the gears are out of control, then the society will be full of chaos. Besides, gear has played the role in the machine like the heart in human body. Therefore, gear should be very solid and precise, otherwise it is valueless. The motto of our company is "harmony", we have been strived for manufacturing gears of high performance, to make the city and town cleaner and safer. We expect you can support and encourage us as usual.