Adopt Tri-Band GSM/GPRS Industrial Communicator, Support SMS Alarm Function. and Android Phone

Adopt tri-band GSM/GPRS industrial communicator, support SMS alarm function. And android phone

I. The basic functions of the host
1)Adopt tri-band GSM/GPRS industrial communicator, support SMS alarm function.
2)Users can record 10 seconds alarm voice message with the scene location information.
3)Arm & alarm delay function, the delay time is adjustable (00~99 seconds).
4)5 wired and 16 wireless defense zones. Each can arm, disarm and 24-hour arm independently.
5)SMS of each zone (5 wired zones, 16 wireless zones) can be edited independently.
6)Automatic arm and disarm time, convenient for users to control the system work regularly.
7)Can set 5 alarm phone numbers and 5 groups of SMS user numbers.
8)Host power off warning function: Send SMS to inform users if power failure.
9)Intercom function: Can communicate with people at the scene, duplex intercom.
10)Listen-in function: Can hear the voice of people move, dig and other actions at the scene.
11)Our remote controllers can do arm/disarm at home/outside, panic alarm, which is convenient and practical.
12)Can control the system by calling-in, such as arm, disarm, listen-in, output remote control, and other functions setting.
13)Password Entering makes the system more secured.
14)Siren interface available for silent and sound siren.
15)Optional built-in auto rechargeable battery, AC and DC auto shift,
16)Wireless alarm system for easy installation, no need to set wire.

II. Identify Interfaces of the host
1. GND; SIREN; RELAY1; RELAY2; SPEAKER; O2(I5); O1(I4); I3; I2; I1

1)10-pin ports: GND; SIREN; RELAY1; RELAY2; SPEAKER; O2(I5); O1(I4); I3; I2; I1
The first port is output for ground end (GND),
The second port is siren output end, the other end of siren connect GND;
The third and fourth port are relay ends, This two ends are normally open and will keep connected for three minutes (this function can be closed)when alarming, This two end control power and video working with two ends open/close.
The fifth port is output of intercom which connects speaker; The other end of speaker connects GND,
The sixth, seventh, eighth, ninth and tenth port are wired input, every port short-circuit or disconnected to GND will trigger alarm.
2)SIM card slot: Turn over the host to the bottom, take out the SIM card tray, put SIM Card in and insert it back.
3)Record key: Press RECORD key for 2 seconds to enter recording status.
4)Reset key: Press RESET key on the back of the host and then plug in power. Then the signal light flashes once or the siren sounds a "di", means the alarm system has been reset. After reset, all settings come back to factory settings, all of the detectors information will be deleted, the original password is 123456, it does not affect SMS control and other functions.
5)Power slot: Connect DC 12V/1.2A, the core is positive pole, the crust is negative pole.
6)Built-in battery switch: Connect to Built-in battery when the switch turn to "ON", at this time external power will recharge the battery automatically.
7)Antenna: Users should connect antenna before insert the power supply.



Technical parameters:
Standby current: 80mA
Working current: 300mA
Power supply: 9 to 12V DC
Operating temperature: -10 to 40° C
GSM frequency: 900, 1, 800 and 1, 900MHz (bands)
Receive coding: Ask
Receive frequency: 315 and 433MHz
Remote control distance: 100m (no obstacle)
Detectors: 16

All trademarks shown here are for reference purposes only. They are the property of their respective owners, and we are not authorized to sell items bearing such trademarks.