It is a new class of a counter surveillance device. Unlike all typical searching devices it can detect modern 'hidden' bugs which use such protocols as Bluetooth and Wi-Fi. Such bugs, especially Bluetooth types, are practically undetectable by common RF detectors due to their very low transmitted power and a special type of modulation. The Protect 1206I uses a separate channel with a high, (2.44GHz) frequency pre-selector to detect and locate Bluetooth and Wi-Fi with a much higher sensitivity. The unit also then processes the demodulated signal in order to identify which protocol has been detected. In addition the unit can detect all 'classical' eavesdropping devices and inspect them for the presence of correlation by sending sound impulses.
Main features
The perfect tool for searching for digital and analogue transmitting eavesdropping devices
Detection of Bluetooth and Wi-Fi. Recognition of other transmissions (GSM, DECT)
Frequency range: - Main antenna 50-4000 MHz; - Auxiliary antenna 2.44 GHz
16-segment bar graph indicator
3 modes: Sound, vibration and mixed
Correlation function - discovers FM-transmitters by the presence of correlation (probing sound is used)
2 levels of sensitivity (attenuator)
Good resource of battery (Long battery life)
Durable metallic body
Microprocessor controlled
Usage. Sweeping the room
Before starting sweeping, some preparation tasks should be carried out. Firstly, it is necessary to consider the time and individual circumstances of the sweep. Due to there being lots of devices which are remotely controlled it is recommended to carry out a sweep during working hours in real situations when the eavesdropper most wants to listen. It may be necessary to arrange a fictitious meeting. Nobody has to know about the pending search.
Close all drapes in the room. Turn on all the lights and activate any other devices to imitate normal conditions. It is also advisable to turn on a source of sound such as a stereo system or radio. This sound source has two very important functions:
Voice activated transmitters will be activated
Your actions will be masked
Leave the room, turn on your iProtect 1206I (7) and select ANT1 (9). Watch the bar graph (6) and if it shows an increased level (more than 4-5 segments), turn on the attenuator by pressing the ATT+ button (8). This procedure measures the background noise of the surrounding area.
Choose the operation mode with the help of the MODE button (4).
For covert procedures use the vibration mode.
The sound mode is more convenient for locating and inspecting the RF source.
The vibrating or mixed mode allows the operator to avoid constantly watching the bar graph when inspecting areas that are difficult to access.
The sound mode allows the operator to listen to the signal so that he or she can understand more about the source. The FM-modulated transmitter (bug) can produce a 'loopback effect' when the unit is close to it or cause the effect of a disappearance of the background noises, which are usually present further away from the transmitter. In this case the 'hum' which can be heard in other parts of the room can disappear when the iProtect 1206I approaches the transmitter and there is a silence on the speaker. In this case it is recommended to use the 'CORR' function (10) while watching the 'DEMODULATION' display (3). Simultaneous fluctuations will warn of the danger.
Enter the room holding the iProtect 1206I while watching its bar graph or paying attention to the vibrator. Turn the lights and other equipment in the room on and off. Walk around the room, continuously watching the indicator or feeling for the iProtect's vibration. The bar graph level will increase or decrease when the detector is closer to, or farther away from a transmitting device.
|
Frequency range |
Antenna 1: 50-4000 MHz;
Antenna 2: 2.44GHz |
|
Power |
Two AAA batteries (2XLR03) |
|
Dimensions |
Without antennas: 120X70X16 mm
With antennas: 220X70X16 mm |
|
Current consumption |
Up to 30 mA |
|
Operation duration |
Up to 20 hours |
|
Indications |
Active antenna, Low battery, Mode, Identification, Attenuator, Secondary demodulation |
ShenZhen Sky Blue Ocean Technology Co., Limited specializes in supplying the latest and innovative electronic products, our customers all over the world for our high-quality, high efficiency, excellent service, in order to standardize quality management, coshine products were manufactured strictly according to ISO 9000: 2000.
Our mission: Coshine strives to be a new world company that makes the best electronic products for our customers. We operate as a company uninhibited by walls or organizational structures using worldsourcing to harness the power of innovation across our global demand.
Our advantage:
Products: We provide innovative and exciting products and services to help our customers success
Price: We have been striving effective management to reduce operation cost, so that we can offer better price to our customers.
Service: We can deliver your items quickly under the customer demand; We promise we can replace new or repair it for free if the item itself has any quality fault.
