Epistar Chip CRI>80 40W LED Panel Light 620X620 3200lm

Epistar Chip CRI>80 40w led panel light 620x620 3200LM

Advantages of our TUV GS mark led panel light::
1.CE/RoHS/TUV/GS certificated.
2. Japan MITSUBISHI 3 MM LGP  + 1.5MM PS Diffuser.
3. Lifud driver+Espistar led.
4. Fast delivery.
5. Thickness: 7.2mm/ 11.1mm/ 47mm
6. 80lm/W, 100lm/W or 120lm/W are available.
7. 600*600, 300*1200, 620*620

Features of ceiling lighting square  LED panel 600x600 with TUV and GS approved:
1. Energy saving: the brightness of the panel light than the equivalent of about 60% reduction in power consumption, power consumption than equivalent incandescent brightness decrease of about 80%, power PFC ≥ 92%, power conversion efficiency ≥ 88%, consistent with energy efficiency standards.

2. Environmental protection: infrared and ultraviolet spectrum free, free of harmful substances mercury content, meet RoHs requirements, led light source is typically green.

3. Life: LED life of up to 50,000 hours, or point that is light, there is no delay time, switching frequency does not affect the light source life.

4. Security: not easily damaged, green. Recyclable waste, no pollution; unlike fluorescent lamps contain mercury components panel, soft light, through the CE certification.

5. Wide scope of application: start at low temperature, normal and use. Common fluorescent panel lamp difficult to start at low temperatures, due to unique design, LED panel lights (special materials: aluminum shell + LGP + spread sheet), light emitted by the surface uniform light, look no glare, greatly reducing human eye injury, relieving eye fatigue, especially for hospitals.

6. Adaptation places: hospitals, offices, retail stores, supermarkets, schools, hotels, factories, car parks and other indoor places to use.

2ft*2ft LED Panel Light Installation:

A. Recessed installation
1. As the image-1, cut a hole with suitable size on the ceiling, and set the T-shape keel beam in advance(please refer to the products cut hole size table);
2. Make the lamp house installed in the hole, then connect the electric supply L, N electrodes to the related Led controllers' L, N.;
3. Set the lamp body steadily on the T-shape keel beam, turn on the power;
Attention: If your T-shape keel beam cannot be able to bear the lamp's weight or any other risks, please add the steel ropes to guarantee the installation's stable.


B. Surface mounted installation
1. As the image-2, set the steel ropes fixed on the ceiling.
2. Set the steel steel ropes connected to lamp house stability, then adjust the rope length to make the lamp house on horizontal position.
3. Connect the electric supply L, N electrodes to the related Led controllers' L, N.
4. Turn on the power
Attention: The led light source cannot to be replaced, please do not open the lamp body or unscrewed the screws among the LED light source, or the heating performance of the LED light source will be influenced, make the lifespan shorter, even the led burnt.
C. Suspension installation

Caution:

1. The lamp body cannot be able connected to the AC Commercial power directly, must via the led controller to supply.

2. According to the actual requirements, equip with the appropriate accessories, confirm the installation before put an order.

3. Cut off the power when you install or remove the light to protect exposed wiring.

4. Do not use organic solvents to clean the surface to prevent corrosion of plastic diffuser.

5. For good heat dissipation, suggest tearing up the protective film of the aluminum backboard after installation.

Specification

Part number	Panel size	Certification	Power(W)	Efficiency	Total lumen	LGP kits details	Light source
PC01D042N40A1	595*595*47mm	TUV CE RoHS GS	40	80	3000-3200lm	1.5mm PS diffuser 88% transparency	42pcs smd3030+lens
PC02D042N40A1	619*619*47mm	TUV CE RoHS GS	40	80	3000-3200lm		42pcs smd3030+lens
PC03D048N40A1	295*1195*47mm	TUV CE RoHS GS	40	80	3000-3200lm		48pcs smd3030+lens
Part number	Panel size	Certification	Power(W)	Efficiency	Total lumen	LGP kits details	Light source
PA01A120N40A1	595*595*7.2mm	TUV CE RoHS GS	48	80	3600-3800lm	Japan MITSUBISHI 3mm LGP + 1.5mm PS diffuser	120pcs smd2835-18*35mil
PA02A120N40A1	619*619*7.2mm	TUV CE RoHS GS	48	80	3600-3800lm		120pcs smd2835-18*35mil
PA03A240N40A1	295*1195*7.2mm	TUV CE RoHS GS	48	80	3600-3800lm		240pcs smd2835-10*30mil
Part number	Panel size	Certification	Power(W)	Efficiency	Total lumen	LGP kits details	Light source
PC01D054N48A1	595*595*47mm	TUV CE RoHS GS	48	80	3600-3800lm	1.5mm PS diffuser 88% transparency	54pcs smd3030+lens
PC02D054N48A1	619*619*47mm	TUV CE RoHS GS	48	80	3600-3800lm		54pcs smd3030+lens
PC03D060N48A1	295*1195*47mm	TUV CE RoHS GS	48	80	3600-3800lm		60pcs smd3030+lens
Part number	Panel size	Certification	Power(W)	Efficiency	Total lumen	LGP kits details	Light source
PC01A480N48A1	595*595*47mm	TUV CE RoHS GS	48	120	5500-5800lm	1.5mm PS diffuser 88% transparency	480pcs smd2835-10*30mil
PC02A480N48A1	619*619*47mm	TUV CE RoHS GS	48	120	5500-5800lm		480pcs smd2835-10*30mil
PC03A480N48A1	295*1195*47mm	TUV CE RoHS GS	48	120	5500-5800lm		480pcs smd2835-10*30mil
Part number	Panel size	Certification	Power(W)	Efficiency	Total lumen	LGP kits details	Light source
PA01A120N48A1	595*595*7.2mm	TUV CE RoHS GS	48	80	3600-3800lm	Japan MITSUBISHI 3mm LGP + 1.5mm PS diffuser	120pcs smd2835-18*35mil
PA02A120N48A1	619*619*7.2mm	TUV CE RoHS GS	48	80	3600-3800lm		120pcs smd2835-18*35mil
PA03A120N48A1	295*1195*7.2mm	TUV CE RoHS GS	48	80	3600-3800lm		240pcs smd2835-10*30mil
TUV GS CE RoHS approved LED panel light remarks:
1. CRI>80
2. Any sample order below 100pcs adding 3USD/pcs sample handle fee
3. For 5 years warranty, adding 3USD for driver . (3)For Recessed/Spring/hanging installation kits +2USD/pcs.
4. For surface mounted installation kits + 8USD/pcs.
5. For flicker free +2USD/pcs
6. For 0~10V dimmer adding 3USD/pcs.
7. Panel aluminum frame both aluminum color and white color available
8. For Recessed/Spring/hanging installation kits +2USD/pcs.