Our multi-frequency remote control duplicator can be used for security systems, roller doors, shutters, sliding gates, barriers and household equipment. This is the only remote control duplicator in the market that permit to duplicate ASK (AM) and FSK (FM)original remote control in different frequency. It can duplicate almost fixed code remote control in the market. It is easy to operate without opening the enclosure and without external programmers. No DIP switches, no trimmers, nothing that needs to be tuned.
You can store a code in each button even with difference frequency.
For example you can store on buttons:
1. FAAC 315MHz
2. Multicode 310MHz
3. Hormann 868.3MHz
4. Marantec 433.92MHz
And it can AUTO- GENERATE ASK HT12E code and FSK HT12E code in each button even with different frequency.
For example you can generate on buttons:
1. ASK 315MHz HT12E
2. ASK 330MHz HT12E
3. FSK 433.92MHz HT12E
4. FSK 868.3MHz HT12E
To remove the existing code: Press button 1 and 2 simultaneously until the red LED flashes, release both buttons and all codes will be deleted
To duplicate code:
1. Choose the duplicate mode you wish, then press the button (where you wish to duplicate the original remote control). The red LED will flash quickly then flash the same times slowly as the times you press the button. The amount of times that corresponds to your desired frequency (see column N in fig 1)
2. Hold the original remote control button during the duplicator LED flash slowly and keep it 2cm-7cm from the duplicator, the LED will steady on during duplicator process. When the code is duplicated successfully, the red LED will flash 3 times slowly then flash quickly enter into sleep mode. Note: If the red LED flash 6 times, which means the original remote control is rolling code. (Eg. To duplicate a remote control at ASK 433.92MHz on button 1, press button 1 twice, the red LED will flash qucikly then flash twice slowly. )
3. Code retrieval: If the code is inadvertently removed, the previous code can be retrieved by pressing buttons 3 and 4 until the red LED flashes. (approximately 5 seconds)
AUTO-GENERATE ASK HT12E code
1. Press button 1 and button 4 simultaneously until red LED flashes 3 times slowly then go into quick flashing, release both buttons.
2. Press any button you want to auto-generate a ASK HT12E code, the amount of times that corresponds to your desired frequency (see the column N in Fig 2)
3. When the red LED flashes quickly, there will generate one ASK HT12E code.
4. The red LED will flash approximate 1.5seconds quickly, if you want to generate one ASK HT12E code on the next button, you need to repeat the step 2 within 5 seconds, otherwise the red LED will flash 5 times slowly after quick flashing then exit AUOT- GENERATE code mode and enter into sleep mode.
N Frequency in MHz N Frequency in MHz
AUTO-GENERATE FSK HT12E code
1. Press button 2 and button 3 simultaneously until red LED flashes 3 times slowly then go into quick flashing, release both buttons.
2. Press any button you want to auto-generate one FSK HT12E code, the amount of times that corresponds to your desired frequency (see the column N in Fig 3 )
3. When the red LED flashes quickly, there will generate one FSK HT12E code.
4. The red LED will flash approximate 1.5seconds quickly, if you want to generate one ASK HT12E code on the next button, you need to repeat the step 2 within 5 seconds, otherwise the red LED will flash 5 times slowly after quick flashing then exit AUOT- GENERATE code mode and enter into sleep mode.
N Frequency in MHz
Note: When multi-frequency remote control duplicator transmitt ASK signal, the red LED is on, when transmitter FSK signal, the red LED will blink.
Battery status and replacement
While pressing the button to transmit, the LED will blink 8 times, it can not work with the receiver, which will notify you low battery status. So you need to replace 1 new piece CR2032 battery.
|
Model No. |
JJ-CRC-SM05 |
|
Configuration Files |
SAW Resonator |
|
Technical Parameter |
ASK and FSK |
|
Frequency |
Multi-frequency remote control duplicator |
|
Battery Model |
CR2032 |
|
Voltage |
6V |
|
Dimensions(L x W x T) |
63*38*12mm |
|
Net Weight |
29.9g/pc |
|
Gross Weight |
33.9g/pc |
|
Packing |
25PCS/BOX |
|
Packaging Parameter |
500PCS/CTN |
|
Carton Dimension |
53.5*22.5*35cm |
|
Certification |
ISO9001:2000,SGS,D&B,BUREAU Intertek and CE |
|
Encoder Model |
Can copy most of remote controls with fixed code in the market and frequency |
Giant Alarm System Co., Ltd. is a high-tech company that specializes in intelligent wireless systems. Our company has the ability to carry out R & D, production and sales. We are a professional manufacturer of RF remote controls (transmitters, keyfob and receivers), remote control duplicators, receiver modules, sliding gate motors and controls, swing gate motors and controls, barrier gate motors and controls and many other mechanical-electrical integrated remote control systems.
Giant has a strong commitment towards R & D, we have the ability to continuously develop new products to meet with customers' different demands. We have adopted micro-computer technology and incorporated logic control to provide products with reliablity, quality and stable functions. Giant has been engaged in the field of producing alarm systems since 2000, we have established a mature marketing network and enjoy a great relationship with our customers.
Giant's business is based on high quality and good service, our aim is to promote development and create new brands which would be of mutual benefit for both companies and achieve a win-win situation. The core values of our company are integrity, honesty, responsible innovation and team work.
We welcome all inquiries from both domestic and overseas companies, and look forward to discussing your requirements.
