1. ) RS-5A 18L Hand Push Cold Paint Road Marking Machine
RS-5A Hand Push Cold Paint Spraying Road Marking Machine is specialized airless spraying equipment for marking highway, provincial road axis, national and municipal highway and airport, parking lot, countryside road, roadway, lane line, stabling siding, dotted line, real line, curved line, arrow, letters, zebra crossing, etc. and can spray common paint and water or cold solvent paint or two component paint. The machine has the features of flexible operation, small size, light weight, marking clear and full lines, spraying high adhesive force of paint and a wide range of applications in spraying.
Engine: Japanese Honda 5.5HP four-stroke air-cooled gasoline engine.
Principle: The machine adopts HONDA gasoline engine which drives plunger pump to make reciprocating movement with the high pressure, which can spay the cold paint with high flow rate and high efficiency.
Spray gun: The standard two spray guns own hard side columnar reverse wastewater nozzle, which makes the site discharging very convenient and fast; the nozzle ensures the base line collimated. The lengthening pipe can be used for normal spraying, such as spraying arrow-head, letter, pedestrian line and so on.
Chassis: The firm welding frame, whose surface has been electrostatic sprayed and high temperature treated, the spraying paint tank with anti-corrosion treatment.
Wheel: The rubber wheel adopts original technology and has the characters of good quality, moderate hardness, good elasticity, high temperature resistance, wearproof, aging resistance and exclusive use. It is equipped with high quality bearing, which makes the whole machine more lightsome.
Rear wheel locating pin: It is the directing device located at rear wheel, can adjust the direction easily and precisely to ensure the machine freely operated in straight or twist.
Available paint: water based or cold solvent paint or two component paint
Guide rod: Freely adjust up, down, left and right.
Paint tank: Special paint tank can improve the work efficiency. There is an intake sieve in the feeding port.
Main Technical Specifications
Size (L×W×H): 1400*850*1050 mm
Net Weight: 180 kg
Power: 9 HP gasoline engine
Working Pressure: 10-18 Mpa
Spraying Thickness: 0.1-0.6 mm
Spraying Width: 50-300 mm (single gun)
50-500 mm (double gun)
Spraying Flow Rate: 18 L/min.
Quantity of Spraying Guns: Standard 2 guns and Max. 4 guns
2. )RS-5B 6L Hand Push Cold Paint Road Marking Machine
RS-5B Hand Push Cold Paint Spraying Road Marking Machine is airless spraying machine with high pressure and steady flow. This machine makes use of the gasoline engine driving the hydraulic system, which drives the single plunger pump and makes the paint having a high pressure inside and sprays the lines. The thickness of the line is even and the corner of line is neat, the guide peg of spraying rack is lifting design, which is convenient and accurate for adjusting the width of spraying line. It has the characters of low working intensity, easy and fast for spraying.
Main Technical Specifications
1. Power: 5.5 HP Gasoline Engine
2. Working Pressure: 10-18 Mpa
3. Spraying Flow Rate: 6 L/min.
4. Spraying Width: 50-300 mm (single gun)
5. Spraying Thickness: 0.1-0.6 mm
6. Size: 1400*800*1050 mm
7. Net Weight: 145 kg
8. Quantity of Spraying Guns: Standard 1 gun and Max. 2 guns
3. ) RS11 Booster Vehicle
It can be connected with RS-5A and RS-5B Hand Push Cold Paint Road Marking Machine, so that you can drive the machine for road marking, will save the manpower and enhance the working efficiency greatly.
Simple Specifications:
1. Max. Climbing Angle: 60°
2. Size: 1500*1200*700 mm
3. Net weight: 80 kg
4. Engine: 5.5 HP American Engine
Operation Steps:
1. Start the engine, connect the towing hook.
2. Release the brake.
3. Press the treadle forward, then it will move forward, deeper press the treadle forward, faster moving speed forward; Press the treadle backward, then it will move backward, deeper press the treadle backward, faster moving speed backward.
4. ) RS-5C Truck-mounted Cold Paint Road Marking Machine
It is a professional equipment for road marking and widely used in highway, national road, city road, airport and parking area for marking the center line and the lane line.
Main Accessories:
1. 270 Japan Honda engine / diesel engine
2. Hydraulic Pump
3. Oil Tank
4. Pressure Regulator
5. Accumulator
6. Commutator
7. Reversing Cylinder
8. Paint High Pressure Pump
9. Filter Screen
10. Air Compressor
11. German Siemens Automatic Breaking Machine
12. German Siemens Manual Controller
13. One Set of Gun Rack
14. Italy Solenoid Valve
15. Two pieces of Automatic Guns
16. Four Pieces of High Pressure Horses (3.5 m)
17. 15 m High Pressure Horse, one piece of Manual Spraying Gun
18. Japan Revolving Encoder
19. Two pieces of Paint Tanks
20. One Water Line Rack
Main Parameter of the equipment
1. Max. Flow Rate: 30 L
2. Max. Working Pressure: 30 Mpa
3. Weight: 820 kg
4. Spraying Width: 50-900 mm
5. Spraying Thickness: 0.1-0.6 mm
6. Size: 1530×1230×1380 mm
7. Can spray four spraying guns at the same time
8. Capacity: 18 L×2
9. Quantity of Spraying Guns: Standard 2 guns and Max. 4 guns
5. ) RS-6A Road Marking Remover
Description
RS-6A Road Marking Remover is a professional equipment applicable to remove the original old marking for the purpose of repairing and renewing the thermoplastic or cold marking line. The machine has the features of strong power, high speed, easy and safe operation, low vibration and noise and dustproof, which can meet all your requirements of removing old marking lines.
Specification
1. Engine: 9.0 HP Honda Gasoline Engine.
2. Rotation Speed: 3600 r/min.
3. Working Width: 220 mm
4. Removing Depth: 0-4 mm
5. Removing Speed: 500-700 m²/day
6. Removal Cutter lifetime: 80 hours, 2000-3000 m²
7. Size: 500*600*1000 mm
8. Net Weight: 110 kg
9. Driving Method: Self-propelled
6. ) RS8 High Pressure Road Cleaning Machine
The gasoline engine of the machine drives the steel brush rotation and polish, doing the cleaning work. It is mainly applied to clean the laintance, mud, surface dust and cold paint line on the road. The regulator is used to regulate the high,middle,low (three level) cleaning strength according to working requirement.
This machine can enhance the adhesive force between the road line and the ground, greatly improve the efficiency of cleaning work before road marking. This machine is one necessary machine for high grade road.
Main Technical Specifications
Model | RS8 |
Size | 1150*620*760 mm |
Weight | 40 kg |
Engine | Imported Honda 5.5 HP gasoline engine |
Rubber wheel | iron hub and special wear resistant rubber |
Material of Brush | wear resistant soft steel wire brush |
7. ) RS7 High Pressure Road Air Blower
This machine is the auxiliary equipment for thermoplastic and cold paint road marking projects. It is mainly applied to the cleaning work before road marking construction. It adopts gasoline engine as the power and make the high pressure impeller of blower rotate and form very strong wind pressure, which clean the dust and impurities on the road. The blower is equipped with primer barrel rack, can finish the clearning and painting the primer at the same time, which can save time and energy and enhance the work efficiency. It is often matched with the Road Cleaning Machine for working.
Main Technical Specifications
Model | RS7 |
Size (L*W*H) | 600×500×800 mm |
Weight | 30 kg |
Max. Wind | 12 m/s |
Wind power | Can be controlled by accelerator |
Impeller | Turbocharging impeller |
Engine | Imported Honda 5.5 HP gasoline engine |
Handle | Can be adjusted to be up and down |
8. ) RS10 Waterline Pre-marking Machine
1. It can mark three benchmark water line at the same time, but firstly you have to have one benchmark line for this machine, which is marked by manual.
2. Max. Width: 9 m
3. Size: 1300×900×1000 mm
4. Net weight: 128 kg
9. ) Cold Solvent Road Marking Paint
ROADSKY Cold Solvent Road Marking Paint is composed of modified acrylic acid resin, pigments, fillers, auxiliary agents and other materials. It is suitable for application to asphalt and concrete roads and often be used for road marking on city streets, national and province roads, parking lots and road-edge stones.
It can be successfully applied to airless or air auxiliary spraying equipment. The road lines width and thickness can be adjusted by adjusting the spraying gun height, nozzle size, pump pressure and moving speed. It can also be successfully applied with a brush or roller for smaller applications.
It is widely used because of its advantages such as low construction cost, high construction speed, convenient operation, strong adaptability and etc.
Main Parameters
Physical Characteristics | Standard | Result |
State in container: | No agglomeration, crust, easy to stir uniformly | Pass |
Density | Min. 1.2 g/cm3 | 1.48 g/cm3 |
Viscosity: (daubing 4 cups) | Min. 100 s | 145 s |
Drying time of no sticking to wheel | Max. 15 minutes | 9 minutes |
Covering Power | White | Min. 95 | 98 |
Yellow | Min. 80 | 85 |
Luminance factor | White | Min. 75 | 81 |
Yellow | Min. 45 | 52 |
Adhesiveness (By circle method) | Max. 4 | 2 |
Abrasion Resistance (200r/1000g reduce weight) | Max. 40 mg | 22 mg |
Flexibility | Max. 5 mm | 1 mm |
Solids content | Min. 60 % | 72 % |
Construction mode | Spraying, brush coating, roller coating |
Quantity per square meter | About 0.35-0.4 kg/m²(about 0.3 mm thickness) |
Service life | 3-12 months according to the vehicles' flowrate |
Main Advantages
1. Visual sense: The adhesive power to glass beads is good, the visual sense during night and rainy night is nice.
2. Road Remarking: It is not necessary to clean the old road marking paint, the remarking is convenient.
3. Road Marking: The road marking is simple, the energy consumption is small.
4. Cost: The equipment is simple and the total cost is lower compare to thermoplastic road marking
5. Anti-dirty: It is good
5. Road Marking Equipment: You could choose the hand-push and truck-mounted machine according to your needing
10. ) Water Based (Borne) Road Marking Paint
It can be successfully applied to airless or air auxiliary spraying equipment. The road lines width and thickness can be adjusted by adjusting the spraying gun height, nozzle size, pump pressure and moving speed. It can also be successfully applied with a brush or roller for smaller applications. It is widely used because of its advantages such as low construction cost, high construction speed, convenient operation, strong adaptability and etc.
Main Parameters
Physical Characteristics | Standard | Result |
State in container | No agglomeration, crust, easy to stir uniformly | pass |
Density | Min. 1.6 g/cm3 | 1.66 g/cm3 |
Viscosity | 80-120 KU | 92 KU |
Drying time of no sticking to wheel | Max 10 minutes | 7 minutes |
Covering Power: | White | Min. 95 | 98 |
Yellow | Min. 80 | 85 |
Luminance factor: | White | Min. 75 | 84 |
Yellow | Min. 45 | 52 |
Abrasion Resistance (200r/1000g reduce weight): | Max. 40 mg | 25.3 mg |
Flexibility | Max. 5.0 mm | 1.0 mm |
Solids content | Min. 75 % | 78.8 % |
Main Features
1. Green environment protection: Because of its high solid content and no content of organic solvent, there is no pollution to the environment and human body during the production or construction.
2. Good toughness and abrasion resistance: The solid content and the inherent characteristics of water-based paint ensure the good adhesion strength with glass micro-beads, so it has excellent toughness and strong abrasion resistance, which bring special use life for water-based line-marking.
3. Good reflective effect: the force of adhesion is good as long as the film reach 0.7 mm, together with adding big reflective glass beads, so there is a very bright reflective effect at night.
4. Good rainy night reflective effect: even on rainy night, there is a good reflective effect, because of the unique structure and the weak hydrophilic nature of water-based paint, together with suitable reflective microcrystalline ceramic beads, there is a remarkable reflective effect even submersed in water.
5. Dry fast, surface drying time 5-10 minutes, easy to clean equipment.
Packaging
25kg per steel drum
Notices
1. Well stirred before use and should be kept under shade.
2. No need to dilute the product with water or solvent.
3. Proper sealed piping should be used, thoroughly rinsed the system with clean water after used.
4. Water washed or soap the spray nozzle into water during application breaks.
5. If heating is needed, the temperature should not exceed 40°C;
6. Application is not recommended whenever the road surface is wet, dirt or when the weather condition is not suitable, such as above 85°C, or temperature below 10°C, or likely to rain with the few hours;
7. Use appropriate equipment.
11. ) Reflective Glass Beads
1. Description
Glass Beads are tiny spheres of glass that used in road marking paint and durable road markings to reflect light back to the driver in dark or poor weather conditions - improving safety and visibility. The glass beads play a very important role in the road safety.
During daytime the white road markings gives the sufficient visibility as a contrast to the asphalt. In the night time contrast of the white line is not sufficient and must be improved by adding light reflective glass beads.
2. Technical specification
Hardness | 6-7 Mohs |
Specific Gravity | 2.4-2.6 g/ cm³ |
Bulk Density | About 1500 kg/ m³ |
Shape | Spherical |
Free Silica | NIL |
Free Iron | <1% |
Color | Clear |
Roundness | ≥80% |
Refractive index | ≥1.5 |
SiO2 | 71-73% |
Na2O | 13-15% |
MgO | 3-5% |
CaO | 8-10% |
Al2O3 | 0.5-2% |
K2O | 0.2-0.6% |
Others | ≤2% |
3. Application
Drop on: This type glass beads are dropped or sprayed onto the surface of liquid road lines during the road marking process.
4. Package
The Glass Beads are packed by double-deck plastic woven bag, 25 kg per bag. Normally 48 bags per pallet, total 20 pallets loaded into one 20' container.
1000-1200 kg big bag with double-deck package, the inner is polythene film and its thickness is not less than 0.5 mm. Normally 20 big bags loaded into one 20' container.
5. Specification
Size (μm) | Percentage (%) |
>212 | 0 |
212-90 | 96-100 |
<90 | 0-4 |
Nanjing Roadsky Traffic Facility Co., Ltd. is located in Nanjing city, 60km away from Nanjing International Airport and 10km away from the entrance of highway. ROADSKY is near to Yangtze River and 300 kilometers away from the eastern deepwater port wharf - Shanghai Port. We are a professional traffic facilities manufacturer in China specialized in developing, manufacturing and exporting traffic facilities including Guardrail Installation and Repairing Machines, Highway Guardrails, Guardrail Accessories, Road Marking Machines, Road Marking Paint, Reflective Glass Beads, Road Studs, Multiple Hammers Concrete Road Breakers, Asphalt Road Recycling Machines and other road safety products. Our main products have passed the test conducted by National Traffic Bureau.
Our company has an efficient management system and advanced manufacturing equipment. Our strong R&D team, excellent product quality, timely delivery, perfect services, special functions and competitive prices help us win the trust and high reputations of numerous customers in domestic and overseas markets. Now our products have been sold to clients in North America, Middle & South America, Europe, Africa, the Middle East, Southeast Asia, Australia and other countries and regions.
We not only supply the above road construction machines and materials, but also supply the services and solutions to all kinds of road construction projects, such as guardrail installation project, road marking project, concrete road breaking project and etc. Our guardrail installation teams and road marking teams have several thousands miles of guardrail installation and road marking projects construction experience in China. Depending on the strong company and teams, we are planning to expand our business of road construction projects to abroad, even though you are a new comer to this business, we can cooperate with you and assist you to solve all the problems, such as supply all the necessary information in order to win the bids, assist you to calculate all the cost of the machines, materials and manpower, the time and other details, we can also dispatch our engineers to your country and train your workers so that you can finish the new road projects by yourselves in the future. We can also dispatch our teams to your country and finish the road projects according to your requirements.
Welcome your enquiry and we promise to give you timely response. If you are interested in our products, please do not hesitate to contact us directly or visit our factory for more information. We are looking forward to establishing long-term business relationships with you and serving your esteemed company in the near future.