Features:
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP67 / IP65 design for indoor or outdoor installations
Type HL LED Driver for use in Class I, Division 2 hazardous location luminaires
Three in one dimming function (1~10Vdc or PWM signal or resistance)
Suitable for LED lighting and street lighting applications
Compliance to worldwide safety regulations for lighting
Suitable for dry / damp / wet locations
5 years warranty (Note.10)
DC VOLTAGE: 12V/15V/20V/24V/30V/36V/42V/48V/54V
HLG-240H-12 A
Blank : IP67 rated. Cable for I/O connection.
A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance.
D (optional) : IP67 rated. Timer dimming function, contact MEAN WELL for details.
Specification:
| MODEL | HLG-240H-12 | HLG-240H-15 | HLG-240H-20 | HLG-240H-24 | HLG-240H-30 | HLG-240H-36 | HLG-240H-42 | HLG-240H-48 | HLG-240H-54 |
| OUTPUT | DC VOLTAGE | 12v | 15v | 20v | 24v | 30v | 36V | 42V | 48V | 54V |
| CONSTANT CURRENT REGION Note.4 | 16A | 15A | 12A | 10A | 8A | 18 ~ 36V | 21 ~ 42V | 24 ~ 48V | 27 ~ 54V |
| RATED CURRENT | 6 ~12V | 7.5 ~ 15V | 10 ~ 20V | 12 ~ 24V | 15 ~ 30V | 6.7A | 5.72A | 5A | 4.45A |
| RATED POWER | 192W | 225W | 240W | 240W | 240W | 241.2W | 240.24W | 240W | 240.3W |
| RIPPLE & NOISE (max.) Note.2 | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 200mVp-p | 250mVp-p | 250mVp-p | 250mVp-p | 350mVp-p |
| VOLTAGE ADJ. RANGE Note.6 | 11.2 ~ 12.8V | 14 ~ 16V | 18.6 ~ 21.4V | 22.4 ~ 25.6V | 28 ~ 32V | 33.5 ~ 38.5V | 39 ~ 45V | 44.8 ~ 51.2V | 50 ~ 57V |
| CURRENT ADJ. RANGE | Can be adjusted by internal potentiometer A type and C type only |
| 8 ~ 16A | 7.5 ~ 15A | 6 ~ 12A | 5 ~ 10A | 4 ~ 8A | 3.3 ~ 6.7A | 2.86 ~ 5.72A | 2.5 ~ 5A | 2.23 ~ 4.45A |
| VOLTAGE TOLERANCE Note.3 | ±2.5% | ±2.0% | ±1.0% | ±1.0% | ±1.0% | ±1.0% | ±1.0% | ±1.0% | ±1.0% |
| LINE REGULATION | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% |
| LOAD REGULATION Note.8 | ±2.0% | ±1.5% | ±1.0% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% |
| SETUP, RISE TIME Note.9 | 1000ms,80ms/115VAC 500ms,80ms/230VAC at full load |
| HOLD UP TIME (Typ.) | 15ms at full load 230VAC /115VAC |
| INPUT | VOLTAGE RANGE Note.5 | 90 ~ 305VAC 127 ~ 431VDC |
| FREQUENCY RANGE | 47 ~ 63Hz |
| POWER FACTOR (Typ.) | PF>0.98/115VAC, PF>0.95/230VAC at full load (Please refer to "Power Factor Characteristic" curve) |
| TOTAL HARMONIC DISTORTION | THD< 20% when output loading>= 50% at 115VAC/230VAC input and output loading>= 75% at 277VAC input |
| EFFICIENCY (Typ.) | 90% | 90% | 91.50% | 92.50% | 92.50% | 92.50% | 92.50% | 93% | 93.50% |
| AC CURRENT (Typ.) | 4A / 115VAC 2A / 230VAC 1.2A / 277VAC |
| INRUSH CURRENT (Typ.) | COLD START 75A(twidth=570μs measured at 50% Ipeak) at 230VAC |
| MAX. No. of PSUs on 16A | 2 units (circuit breaker of type B) / 4 units (circuit breaker of type C) at 230VAC |
| LEAKAGE CURRENT | <0.75mA / 277VAC |
| PROTECTION | OVER CURRENT Note.4 | 95 ~ 108% |
| Protection type : Constant current limiting, recovers automatically after fault condition is removed |
| SHORT CIRCUIT | Hiccup mode, recovers automatically after fault condition is removed |
| OVER VOLTAGE | 13.5 ~ 18V | 17.5 ~ 21.5V | 23.5 ~ 27.5V | 27 ~ 34V | 33 ~ 39V | 43 ~ 49V | 48 ~ 54V | 55 ~ 63V | 60 ~ 67V |
| Protection type : Shut down and latch off o/p voltage, re-power on to recover |
| OVER TEMPERATURE | Shut down o/p voltage, recovers automatically after temperature goes down |
| ENVIRONMENT | WORKING TEMP. | -40 ~ +70ºC (Refer to "Derating Curve") |
| WORKING HUMIDITY | 20 ~ 95% RH non-condensing |
| STORAGE TEMP., HUMIDITY | -40 ~ +80ºC, 10 ~ 95% RH |
| TEMP. COEFFICIENT | ±0.03%/ºC (0 ~ 50ºC) |
| VIBRATION | 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes |
| SAFETY & | SAFETY STANDARDS Note.7 | UL1012, CAN/CSA-C22.2 No. 107.1-01, UL8750, CSA C22.2 No. 250.0-08, TUV EN61347-1, EN61347-2-13 independent |
| EMC | (except for HLG-240H C type), UL60950-1, UL8750, TUV EN60950-1, IP65 or IP67, J61347-1, J61347-2-13 approved |
| WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC |
| ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25ºC/ 70% RH |
| EMC EMISSION | Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (>=50% load) ; EN61000-3-3 |
| EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria B |
| OTHERS | MTBF | 207.9K hrs min. MIL-HDBK-217F (25ºC) |
| DIMENSION | 244.2*68*38.8mm (L*W*H)(HLG-240H-Blank/A/B) 251*68*38.8mm (L*W*H)(HLG-240H-C) |
| PACKING | 1.3Kg; 12pcs/16.6Kg/0.84CUFT(HLG-240-Blank/A/B) 1.23Kg; 12pcs/15.8Kg/1.16CUFT(HLG-240-C) |
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25ºC of ambient temperature. |
| 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. |
| 3. Tolerance : includes set up tolerance, line regulation and load regulation. |
| 4. Please refer to "DRIVING METHODS OF LED MODULE". |
| 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. |
| 6. A type and C type only. |
| 7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18. |
| 8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. |
| 9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the |
| complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. |
| 10. Refer to warranty statement. |
| 11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently |
| connected to the mains. |
We are committed to providing the best technical and commercial solution for your power needs.
"Total Quality Assurance and Customer Satisfaction" are the central goals of our company. We believe that our industry is one where reliability in long-term use, functionality and cost are all of great importance, but that it is reliability that differentiates the truly superior products. So, every product in the MEAN WELL range is the result of rigid procedures governing design, design verification tes, design quality test, component selection, pilot-run production, and mass production. We have recently implemented a new and highly efficient computerized management system. This system allows improved administration of sales, manufacturing, purchasing, fabrication management, shipping, customer service, and quality analysis, allowing us to ensure the best QCDS (Quality, Cost, Delivery Time, Service) for our customers.
Our goal is to offer total solutions that satisfy our customer's requirements. We have earned a good reputation based on the quality, competitive prices and punctual delivery of our products. Currently, we have thousands of customers throughout the world. We have formed long-term associations with most of our customers, working together for many years, developing many treasured relationships.
For more customized demands that can't be found in our standard product lines, we also can offer Cooperate Design Manufacturer solution to combine your specific requirements into our newly design standard products. Thanks to our extensive library of circuit solutions, we are confident that we can promptly provide satisfied samples for your review and approval.
• Culture and Principle
Corporate Culture
Honesty and Sincerity
Open-minded and Aggressive
Active and Responsible
Harmony and Unity
Principles
Strive for Excellence
Long-term Operations
Profit Creation
Feedback to Society
The core mission of our enterprise is the endless pursuit of innovation and improvement in order to maximize benefit for our customers, employees, shareholders, and society as a whole. We emphasize cultivating each employee's potential, allowing them to develop excellent products that completely satisfy our customer's requirements. This allows our enterprise to create profit. This profit should be shared between employees and shareholders, with some also set aside for the greater needs of society. Furthermore, an enterprise must always invest in its own future, providing the funds needed as it ceaselessly seeks to expand and develop.
We firmly believe that the power supply industry is one built on reliability. The mission of a power supply company should be to engender the utmost confidence in both the technology and quality of its products. Only by constant strides to improve and innovate, can a company stand the test of time and be truly trusted by its customers.
• Vision
To strive for excellence in our long term operation; To always be dedicated to perfectly balancing technology, humanity and the environment; To become an innovative and positive contributor to the world.
To be a long-term reliable partner providing customers with the best P, Q, C, D, S, R.
To be one of the leading branded standard power supply manufacturers in the world.
