Co Removal Catalyst Ceramic Honeycomb Platinum Catalyst

Product Specifications

Markets:	North America,South America,Eastern Europe,Southeast Asia,Africa,Oceania,Mid East,Eastern Asia,Western Europe
Enter Attribute Here (e.g.: Size):	Enter Value Here (e.g.: 12 Inches)
Usage:	Positive Catalyst
Classification:	Homogeneous Catalysts

Product Description

Production Introduction   
 
1. CAS-KR-Y01-F CO removal catalyst)
    CAS-KR-Y01-Fcatalyst works efficiently to remove CO from petro gas, inert gas, oxygen and etc, also could be used in various furnace like oven, chimney place, incinerator to treat not burst CO.
    This catalyst could make CO content less than 0.5ppm under temperature 150~200°C and space velocity at (0.3~1.0)×104h-1; oxygen capacity of this catalyst could be 50ml/g, and catalyze reaction CO and O2 to be CO2.
  
2. CAS-KR-Y01K-F oven exhaust gas purification catalyst
    CAS-KR-Y01K-F oven exhaust purification catalyst is suitable for baking oven, fireplace and other equipment used for the catalytic combustion of unburned CO, purification effect is very good.
 
 
3. CAS-KR-Y01M-F  mosquito magnet catalyst
    CAS-KR-Y01M-F mosquito magnet catalyst belongs to high-tech material products, with the liquefied petroleum gas catalytic oxidation to simulate human CO2 function to attract mosquitoes to mosquito catcher, at the same time,heating and oxidation generated can be used to produce electricity for the mosquito catcher, the product non-toxic harmless, environment friendly products, mainly used in luxury mosquito eradication machine.
 
 
4. CAS-KR-T02-K CO normal temperature removal catalyst
    CAS-KR-T02-K CO normal temperature removal catalyst is using active alumina as carrier, and a unique addition of rare earth materials, with a high content of noble metal Pd, Pt as active component prepared.Can be used for CO at normal temperature within an enclosed environment under the mine rescue capsule / refuge chamber and eliminate, can also be used in submarine cabin, fire mask, CO2 laser, gas shower device with a small amount of CO is required to eliminate in the occasion.The catalyst at normal temperature (≥ 15 °C), air humidity below 90%, space velocity of 0.5 × 104H? 1, 20min CO can be converted, the residual amount of CO ≤ 23ppm, single cycle time is not less than 24 hours, after simple regeneration can be reused for more than 3 cycles.
 
 
    1.1. Operation condition & Technology properties

No	Test item	Technology parameter
		Carrier: cordierite and composite alumina with various specs
1	Space velocity	≥3×103h-1
2	Initial ignition temperature	100°C-150°C
3	Optimal service temperature	180°C-200°C
4	CO removal ratio Service life	≥ 98% ≥2 years
5	Service life	≥ 2 years
5	CO outlet content	<5ppm
6	Bulk density	0.68±0.05g/mL
7	Crushing strength	≥ 14 MPa
8	Coating component	≥ 10.0%
9	Activity component	0.08%-0.2% (also depends on your demand)
10	Expulsion ratio	<1%
11	Appearance	Usually is light yellow (would be grey after pre-reduction)
12	Packing	Moisture-proof
13	Suggested loading height/diameter	Honeycomb type 4:1;2:1particle 1:1

 
 1.2.CAS-KR-Y01-F catalyst Properties
 
  
 
    Before using, CO removal catalyst should be heated up to 180~200°C by fresh ai or nitrogen , in order to active its performance. The optimal operating temperature is 200°C, and removal CO until 0.5ppm left under operation space velocity (0.3~1.0)×104h-1; Max temperature is 750°C (cooling system is required if flammable gas is in high concentration).
 
 
 
    2.1.CAS-KR-Y01K-F Operation condition & Technology properties
 

No	Test item
		31.75×6.35  31.75×12.8
1	Space velocity	≥3×103h-1
2	Initial ignition temperature	200°C-250°C
3	Optimal service temperature	250°C-400°C
4	Service life	≥2years
5	CO outlet content	<4mg/m3
6	CnHm outlet content	<5mg/m3
7	Bulk density	0.68±0.05g/mL
8	Crushing strength	≥12 Mpa
9	Rupture strength	≥2 Mpa
10	Coating component	>10.0%
11	Activity component	≥0.1%
12	Expulsion ratio	<1%
13	Appearance	Usually is light yellow & red(would be grey after pre-reduction)
14	Packing	Moisture-proof

 
 
 
    2.2. The purification principle and characteristics of the CAS-KR-Y01K-F oven exhaust catalyst
 
    The harmful exhaust CO and unburned hydrocarbons CnHm  easily generated in the barbecue process oven equipment.After install the exhaust gas purification catalyst oven, under the action of a catalyst, in the process of exhaust gas temperature rising in the oven, oven exhaust further temperature catalytic oxidation, can produce emissions of CO2 and H2O , so that CO and CnHm can reach the discharge standard,and the oven exhaust purification as the purposes. CAS-KR-K01-F oven exhaust gas purification is in the conditions of catalyst at a temperature of 250~400 °C, airspeed (0.3~1) × 104h？1  , the purified gas, CO and non-methane hydrocarbons content can be reduced to below 4mg/m3; the catalyst can be repeatedly recycled, the mechanical strength is good so that the service life can more than 2 years.
 
 
    2.3. The points for attention in useof CAS-KR-Y01K-F oven exhaust purification catalyst
    Oven exhaust catalyst need  preheat to 200~250 °C activation first, and then run the oven gas to be treated, the better the operation temperature over 300 °C, the reaction conditions of 1.5~3.0 * 103h-1 CO in exhaust can be eliminated to below 0.5ppm, non-methane hydrocarbons can be reduced to below 1 ppm; the highest heat-resisting temperature is 750 °C (if the combustible gas concentration is high,it need to be matched with cooling system, prevent catalyst sintering).
 
    3.1. CAS-KR-Y01M-F mosquito magnet Catalyst specifications

NO.	Test item	specifications
		40.89×6.35 Carrier specifications  40.89×9.652                               40.89×25.4 Other cordierite specifications
1	Light display time	<900s
2	The outlet CO concentration	<0.5mg/m3
3	Service life	≥2years
4	Bulk density	0.66±0.05g/mL
5	Compressive strength	≥12MPa
6	Carrier specifications	According to customer requirements
7	The coating layer of the load	>8%
8	Fall off rate	<1%
9	Appearance	Shallow brown
10	Packing	Moisture seal

 
 
 3.2. Principle of special CAS-KR-Y01M-F mosquito magnet Catalyst)
 
    Mosquitoes are issued by the body of carbon dioxide atmosphere to find people, when they feel the carbon dioxide gas flows immediately they will flew to the air stream; mosquito magnet is a machine that using the liquified petroleum gas to run produce the simulation of human respiratory carbon dioxide concentration and catch the mosquito ; which produce simulated human respiratory carbon dioxide concentration and the elimination of carbon monoxide as core components is CAS-KR-Y01M-F type catalyst for mosquito magnet.
 
 
    3.3. Characteristics of CAS-KR-Y01M-F  catalyst for mosquito magnet
    CAS-KR-Y01M-F mosquito magnet catalyst belongs to high-tech material products, with the liquefied petroleum gas catalytic oxidation to simulate human CO2 function to attract mosquitoes mosquito catcher,at the same time, heat and oxidation generated waste heat can be used to produce electricity for the mosquito catcher used.The product non-toxic harmless, environment friendly products, mainly used for luxury type mosquito killing machine, can also be used in oven, fireplace and industrial CO and VOC gas catalytic oxidation.
 
    3.4. Note of using CAS-KR-Y01M-F catalyst for mosquito magnet
 
    The installation to use inorganic material of high temperature resistant pad, do not need to disassemble the moisture-proof seal after long-term , catalyst wetting caused failures by 110 °C drying or calcined at 500 °C regeneration.
 
 
    4.1. CO normal temperature Removal CatalystTechnology properties
 
 

NO.	Test Item
		2-3(mm)    Composite AL2O3 specification  3-4(mm)                                                                   4-5(mm)
1	Airspeed	>0.5×104h-1
2	(using temperature)	Nomal temperature
3	Service life	≥24h
4	Bulk density	0.65±0.2g/ml
5	Crushing strength	≥60N/Φ2-3(mm)
6	Removal CO depth	≤23.0ppm
7	Resistance to humidity	≤90%
8	Active component load	≥1.0%
9	CO removal rate	≥95%
10	Appearance	Dark gray
11	Packing	Moisture seal
12	Recommended to install the ratio of height to diameter	≥1:1

 
 
    4.2. The operation and maintenance of CAS-KR-Y01-1 carbon monoxide nomal temperature removal catalyst
    CAS-KR-Y01-1 carbon monoxide normal temperature removal catalyst without activation, without preheating, at normal temperature in air purifier used directly.Placed in front of 1:1 catalyst volume when using active carbon or alumina molecular sieve catalyst for moisture.The vacancy please seal packaging, when opened, if damp with constant temperature of 120 °C drying after using 3h.