High Efficiency Water Softener About 200 Gpm

Product Specifications

Prod Model:	YL-II-50
Markets:	North America,South America,Eastern Europe,Southeast Asia,Africa,Oceania,Mid East,Eastern Asia,Western Europe
Control Mode:	Flow Type, Time Type
Resin:	001×7 Strong Acidic Cation-Exchange
Working Ambient Temperature:	5-50centigrade
Relative Humidity:	Less Than 95%(25centigrade)
Hardness Of Raw Water:	Less Than 8mmol/L
Working Principle:	Ion Exchange
Certification:	CE
Inlet Mode:	Pipeline
Installation:	Vertical Type
Heating Mode:	No

Product Description

Working principle
To absorb the calcium and magnesium ions in the water with resin-As the hardness of the water is mainly formed and expressed by calcium and magnesium, the cation exchange resin (water softener)is generally used to replaceCa2 + and Mg2in the water The resin efficiency to removeca2 + and Mg2+ gradually reduces as ca2 + and Mg2 + in the resin increase. When the resin absorbs a certain amount of calcium and magnesium ions, it is necessary to be regenerated. In the regeneration process, the resin bed is flushed by saline in the salt box and hardness ions on the resin are replaced and discharged with recycled waste fluid, the resin's function of softening exchange is recovered. The principle of sodium ion exchanging softening treatment is to use sodium cation exchange resin to exchange the hardness ingredients, Ca2 + and Mg2 +, in the raw water with Na + in the resin, absorbing Ca2 + and Mg2 + in the water, so that water gets softened.

Control modes of automatic water softeners:
(1) Single tank time type: The time control of microcomputer is used, so that the equipment is able to automatically enter into the regeneration state after running for a set period of time. The regeneration can be once a day or repeated every day.
(2) Single tank flow type: The turbine flow control or electronic flow sensor control is used, so that the equipment is able to automatically enter into the regeneration state when its water yield reaches a pre-set flow. The regeneration can be repeated every day.
(3) Dual-tank flow type: It can be divided into Mode? I with one tank for use and the other for standby and Model llwith two tanks for simultaneous operation and respective regeneration.
Model l: One tank runs and the other one stands by. The running tank enters into the regeneration state after its water outflow reaches a set flow and at the same time the standby tank starts running, two tanks running and regenerating alternatively for continuous 24 hours' water supply.
Model II: Two tanks run simultaneously. The first tank continuously produces water while the second tank regenerates first and restarts running after regeneration, and then the first tank starts regeneration. After both tanks finish regeneration, they run simultaneously again.

Characteristics of the stainless steel water tank
1. The water tank manufactured by material deformation using the least material consumption for best strength effect has smooth lines and strong stereoscopic impression and beautifies the appearance of a city.
2. The water tank designed according to stainless steel 02S101 and manufactured with material SUS3O4 and SUS316 has good corrosion resistance and seismic performance. It is easy to be transported without heavy lifting equipment. Tanks of different volumes can be assembled on site.
3. Lt is clean and has high structural strength with less material compared with the traditional water tanks, achieving durable in use and becoming a new trend of the tank industry.
4. Lt can be used for hot and cold water and is an ideal insulation device.

Category	Model	Recommended water yield (M³/h)	Tank size Diameter *Height(mm)	Salt box (L)	Amount of resin(KG)
Single-valve and single-tank	YL-I-0.5	0.5	200×900	25	20
	YL-I-1	1	250×1400	60	40
	YL-I-2	2	300×1400	200	60
	YL-I-3	3	350×1400	100	80
	YL-I-4	4	400×1650	200	120
	YL-I-5	5	500×1750	300	180
	YL-I-6	6	300×1900	350	240
	YL-I-10	8-10	750×1900	500	360
	YL-I-18	42-18	900×1900	800	520
	YL-I-25	18-25	1000×2200	1000	720
	YL-I-35	25-30	1200×2400	1500	1000
	YL-I-50	35-50	1500×2500	2000	6400
Dual-valve and dual-tank (simultaneous operation and respective regeneration)	YL-II-36	24-36	900×1900	800	1040
	YL-II-50	36-50	1000×2200	1000	1440
	YL-II-70	50-70	1200×2400	1500	2000
	YL-II-100	70-100	1500×2500	2000	3200
Dual-valve and dual-tank(One for use and the other for standby)	YL-II-1	1	250×1400	60	80
	YL-II-2	2	300×1400	100	120
	YL-II-3	3	350×1400	100	160
	YL-II-4	4	400×1650	200	240
	YL-II-5	5	500×1750	300	360
	YL-II-6	6	600×1900	350	480
	YL-II-10	8-10	750×1900	500	720
	YL-II-18	12-18	900×1900	800	1040
	YL-II-25	18-25	1000×2200	1000	1440
	YL-II-35	25-35	1200×2400	1500	2000
	YL-II-50	35-50	1500×2500	2000	3200
Dual-valve and dual-tank(JK)	JK25-150	0.2-0.3	200×900×2pc	25	40
	JK25-200	0.5-0.6	200×1200×2pc	60	80
	JK25-250	0.8-1.0	250×1400×2pc	60	120
	JK25-300	1.8-2.0	300×1400×2pc	100	200
	JK25-350	2.8-3.0	350÷1650×2pc	100	240
	JK25-400	3.5-4.0	400×1650×2pc	200	40