Product Specifications
| Prod Model: |
403/406/454435/438 |
| Markets: |
Eastern Asia,Western Europe |
| Adhesive: |
Water Based Glue |
| Type: |
Liquid |
| Material: |
PVC |
| Shape: |
Roll |
Product Description
PRODUCT DESCRIPTION
LOCTITE® 435™ provides the following product
characteristics:
Technology Cyanoacrylate
Chemical Type Ethyl cyanoacrylate
Appearance (uncured) Colorless to straw colored, slightly
cloudy liquidLMS
Components One part - requires no mixing
Viscosity Low
Cure Humidity
Application Bonding
Key Substrates Metals, Plastics and Rubbers
LOCTITE® 435™ is a rubber toughened adhesive with
increased flexibility and peel strength along with enhanced
resistance to shock. The product provides rapid bonding on a
wide range of materials, including metals, plastics and
elastomers, as well as porous and absorbent materials like
wood, paper, leather and fabric.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Specific Gravity @ 25 °C 1.1
Flash Point - See MSDS
Viscosity, Cone & Plate, mPa·s (cP):
Temperature: 25 °C, Shear Rate: 1,000 s-1 100 to 250LMS
TYPICAL CURING PERFORMANCE
Under normal conditions, the atmospheric moisture initiates the
curing process. Although full functional strength is developed
in a relatively short time, curing continues for at least 24 hours
before full chemical/solvent resistance is developed.
Cure Speed vs. Substrate
The rate of cure will depend on the substrate used. The table
below shows the fixture time achieved on different materials
at 22 °C / 50 % relative humidity. This is defined as the time to
develop a shear strength of 0.1 N/mm².
Fixture Time, seconds:
Steel (degreased) 30 to 45
Aluminum (IPA wiped) ≤60LMS
Zinc dichromate 90 to 105
Neoprene 30 to 45
Rubber, nitrile <5
SBR 90 to 105
ABS 10 to 20
PVC 60 to 75
Polycarbonate 45 to 60
Phenolic 10 to 20
G-10 Epoxy 45 to 60
Wood (oak) 75 to 90
Wood (balsa) <5
Cure Speed vs. Bond Gap
The rate of cure will depend on the bondline gap. Thin bond
lines result in high cure speeds, increasing the bond gap will
decrease the rate of cure.
PRODUCT DESCRIPTION
LOCTITE® 438™ provides the following product
characteristics:
Technology Cyanoacrylate
Chemical Type Ethyl cyanoacrylate
Appearance (uncured) Black liquidLMS
Components One part - requires no mixing
Viscosity Low
Cure Humidity
Application Bonding
Key Substrates Metals, Plastics and Rubbers
LOCTITE® 438™ is a rubber toughened adhesive with
increased flexibility and peel strength along with enhanced
resistance to shock. The product provides rapid bonding on a
wide range of materials, including metals, plastics and
elastomers, as well as porous and absorbent materials like
wood, paper, leather and fabric.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Specific Gravity @ 25 °C 1.1
Flash Point - See MSDS
Viscosity, Cone & Plate, mPa·s (cP):
Temperature: 25 °C, Shear Rate: 1,000 s-1 100 to 250LMS
TYPICAL CURING PERFORMANCE
Under normal conditions, the atmospheric moisture initiates the
curing process. Although full functional strength is developed
in a relatively short time, curing continues for at least 24 hours
before full chemical/solvent resistance is developed.
Cure Speed vs. Substrate
The rate of cure will depend on the substrate used. The table
below shows the fixture time achieved on different materials
at 22 °C / 50 % relative humidity. This is defined as the time to
develop a shear strength of 0.1 N/mm².
Fixture Time, seconds:
Steel (degreased) 30 to 45
Aluminum (Isopropanol wiped) ≤60LMS
Zinc dichromate 105 to 120
Neoprene 30 to 45
Rubber, nitrile <5
SBR 75 to 90
ABS 10 to 20
PVC 65 to 90
Polycarbonate 90 to 105
Phenolic 5 to 10
G-10 Epoxy 20 to 30
Wood (oak) 45 to 60
Wood (balsa) <5
Cure Speed vs. Bond Gap
The rate of cure will depend on the bondline gap. Thin bond
lines result in high cure speeds, increasing the bond gap will
decrease the rate of cure.
ShenZhen Joint technology Co., Ltd., /Joint Industry (HK) Limited; Is located in shenzhen baoan district rock town east road (swim town industrial park) 2, 5 / f building, 262 tel 86-0755-36523302 (yan-fei xu), the main loctite products and plastic sticky tape, etc.
ShenZhen Joint technology Co., Ltd., shenzhen city with LED power supply and LED lighting assembly support, to distribution of henkel loctite products development, has become one of the electronics and industrial, provide a full range of adhesives and related solution technology service-oriented enterprises.
In terms of products, like as henkel general industrial dealers, all products can supply henkel group, including Loctite (Loctite), Macromelt, Macroplast, Macrocast brands. In terms of equipment, in addition to UV LED light source, the design and sales of LED power supply, also can provide supporting including loctite dispensing equipment at home and abroad. Another can provide the experiment and the dispensing process for all kinds of customers service, we will strive to become the most professional adhesive and dispensing integration services.
The spirit of "people-oriented, customer-focused, cooperation and win-win" principle, the means of has made rapid development. "The poor are immune to the noblesse", we will make unremitting efforts, create a better future with you!
