Product Specifications
| Prod Model: |
HLQ5250 |
| Markets: |
South America,Southeast Asia,Africa,Oceania,Mid East,Eastern Asia,Western Europe |
| Certification: |
CCC |
| Fuel: |
Diesel |
| Payload: |
20T |
| Engine Type: |
4 Stroke |
| Type: |
Garbage Truck |
| Volume: |
10000-20000L |
Product Description
Sinotruk garbage compactor 16M3
Drive: 6x4 lift hand drive Specifications
Chassis ZZ3257M3847
Engine
Make: SINOTRUK
Diesel: 4-stroke direct injection diesel engine
Engine model: WD615, Euro2, emission standard
6-cylinder in-line with water cooling, turbo-charging and intercooling
Maximum output: 266 HP(196KW)at 2200 rpm
Maximum torque: 1160 Nm at 1100-1600 rpm
Number of cylinder: 6
Displacement: 9.726 L
Bore: 122mm
Stroke: 126mm
Compression ratio: 27.35 HP/L
Specific fuel consumption: 189g/KWh
Engine oil filling quantity: 19L
Cooling system filling quantity(long-term filling): 40 L
Thermostat with 71c opening begin
Single cylinder air compressor
Rigid fan
Driver's Cab
HW76 standard cab, one berth, all-steel forward control, 2 -arm windscreen wiper system with three speeds, laminated windscreen, with casted-in radio aerial, hydraulically damped adjustable driver's seat and rigid adjustable co-driver's seat, with heating and ventilating system, adjustable roof flap, with stereo ratio/cassette recorder, sun visor, adjustable steering wheel, air horn, air conditioner, with 4-point support fully floating suspension and shock absorbers.
Clutch
Single-plate dry clutch, diameter 420mm, hydraulically operating with air assistance
Transmission HW15710, 10 forward, 2 reverse
Propeller Shaft Double universal joint propeller shaft with gear-shaped coupling flange
Front Axle HF7, 7 tons axles, steering with double T-cross section beam
Rear Axle
HW1667, 16 tons axles with one axle driving, pressed axle housing, central single reduction with hub reduction and with differential locks
Ratio: 3.73
Chassis
Frame: U-profile parallel ladder frame with section of 300× 80× 8 mm and reinforced subframe, all cold riveted cross members
Front suspension: 9 semi-elliptic leaf springs with hydraulic telescopic double-action shock absorbers and stabilizer
Rear suspension: 15 leaf semi-elliptic springs with hydraulic telescopic double-action shock absorber
Aluminum fuel tank: 200 l capacity with locking fuel cap, fitted to the off side of the chassis
Steering
ZF8098, hydraulic steering with power assistance
Ratio: 26.2
Brakes
Service brake: Dual circuit compressed air brake
Parking brake (emergency brake): Spring energy, compressed air operating on rear wheels
Auxiliary brake: Engine exhaust brake
Option: ABS
Wheels & Tires
Rims: 8.5-20, 10 hole-steel
Tyres: 11.00-20 tube
Electrics
Operating voltage: 24 V, negative grounded
Starter: 24 V, 5.4Kw
Alternator: 28 V, 1000 W
Batteries: 2× 12 V, 165Ah
Cigar-lighter, horn, headlamps, fog lights, brake lights, indicators and reverse light
Dimensions in mm
Wheel base 3825+1350
Front wheel track 2022/2041
Rear wheel track 1830
Front overhang 1500
Rear overhang 3175
Approach angle( ° ) 16
Depar ture angle( ° ) 15
Overall dimension(L x W x H mm) 9850x2500x3330
Weight in kg
Dead weight 9450
Rated loading capacity 13600
Gross vehicle weight 25000
Performance
Maximum driving speed(km/h) 90
Maximum grade ability(%) 39
Minimum ground clearance(mm) 298
Minimum turning ci rcle(m) 18.6
Fuel consumption(1/100km) 28
Body
Volume of body(m3) 16
Volume of fi l ler(m3) 2.0
Time of one fi l l ing cycle(s) ≤ 25
Li ft ing t ime of f I l ler (s) 8-10
Time of discharge (s) ≤ 40
Front/rear sewage capaci ty (L) 250+150
Max compression force (kg) >25000
Our product range includes water truck, fuel tanker, fecal suction truck, sewage suction truck, tow truck, concrete mixer truck, dump truck, high-altitude operation truck, self-loading garbage truck, garbage compactor truck, sealed garbage truck, powder truck, low plate semi-trailer, grid-type semi-trailer, van semi-trailer, fence semi-trailer, semi-trailer, Bulk cement transportation semi-trailer, oil semi-trailer, container Semi-trailer, chemical liquid transport semi-trailer, etc., more than 300 types in total.
Hubei Heli Special Automobile Manufacture Co., Ltd is one of largest manufacturers of special purpose vehicles in China.
It was set up in 2002. After ten years' fast development, now we have more than 130, 000 square meters plant area, more than 300 sets of advanced equipments, more than 800 professional workers, more than 300 types special purpose vehicles and more than 50000 units vehicles yearly production capacity with the capacity of Independent research and development.
The production facilities include large CNC machine, bending machine, underwater plasma cutting machine, hydraulic machine, forging Machine, tank molding coiling machine, arc welding machine, X-ray detection machine, ect. The total value is more than 600, 000, 000 RMB.
There are more than 100 senior and intermediate technologists, more than 400 senior and intermediate skilled workers, 20 new products engineers, and more than 100 support personnel in our staff team. Now our capacity of Independent research and development is well known in this industry in China.
The company committed to the pursuit of technology research and application of safety, environmental protection, high efficiency, energy conservation, and automation. The products are evaluated to be "Chinese consumers' satisfactory brand", "National band with good quality and satisfactory service", "Well-known brand in Hubei"; And the company is praised as an "enterprise with integrity to comply with the contract"; Listed as banking credit "AAA" grade; Enterprise with new high technologies'; Pass ISO9001 certification and China Compulsory Certification. Meanwhile we are trying to carry out TS16949, ISO14000 and so on certification systems.
At this moment, we already have business in Russia, Denmark, Georgia, Kazakhstan, Algeria, Australia, Bahamas, ect. All our customers are becoming our good friends and long term parters. Welcome you to join us and develop together with honesty.
